Translate

SPN 190 - FMI 2 (Fault Code: Engine Crankshaft Speed/Position - Data Erratic, Intermittent, or Incorrect)

Fault Code 0689 (Cummins QSKTA50-CE)

Figure 1.1 - Engine Crankshaft Speed/Position Sensor

1). Datalink Adapter (USB-Link 2/NEXIQ) is connected to the computer, the key switch is ON, and that power is supplied to the Datalink Adapter (connected to a J1939), and starts the Engine. Read More: How to Connecting CUMMINS Engines using Cummins INSITE Software.

2). Select Fault Codes from the Viewbar.
Figure 1.2 - Fault Codes 0689 and 1518
→Double-clicking on the selected Fault Code (0689), to open the Troubleshooting Manual. Read More: SPN 190 - FMI 0 (Fault Code 234).

REASON = The ECM has detected an error in the Engine speed signal. EFFECT = Possible reduced Engine performance.
Figure 1.3 - Engine Crankshaft Speed/Position Circuit
#Circuit Description
The Crankshaft Position (Main) and Camshaft Position (Backup) sensors are Hall effect type sensors. The ECM provides a 5 volt supply to the position sensor and a return circuit. As the teeth on the crankshaft speed ring or the dimples in the back of the camshaft gear move past the position sensor, a signal is generated on the position sensor signal circuit. The ECM interprets this signal and converts it to an Engine speed. A missing tooth on the crankshaft gear is used by the ECM to determine the position of the Engine.

#Component Location
The Engine Crankshaft Speed/Position Sensor is located on the flywheel housing.

#Conditions for Running the Diagnostics
→This diagnostic runs continuously when the Engine is running.
→The ECM detected a loss of the Crankshaft Speed/Position Sensor while the Engine was running.

#Action Taken When the Fault Code is Active
→The ECM illuminates the amber CHECK ENGINE lamp immediately when the diagnostic runs and fails.
→The Camshaft Position Sensor will be used by the ECM to determine Engine speed and position.
→Engine torque will be reduced if the Engine is operated for an extended period of time with this fault active.

3). Troubleshooting Fault Code 0689
A. Crankshaft Speed/Position Sensor Voltage Check (in the Sensor and ECM connector)
→Disconnect the Crankshaft Position Sensor from the Engine wiring harness/ECM connector.
→Inspect the pins and connectors for damage.
→Measure the voltage (4.75 - 5.25 VDC) between the Crankshaft Position Sensor SUPPLY pin and the RETURN pin at the sensor connector of the Engine wiring harness.

B. Engine Crankshaft Speed/Position Sensor Check
→Remove the Crankshaft Position Sensor.
→Inspect the Crankshaft Position Sensor for signs of damage, oil leak, and metal debris on the end of the sensor.
Figure 1.4 - Engine Crankshaft Speed/Position Sensor (Removed)
→Verify the Crankshaft Position Sensor is connected properly.
→Monitor the Crankshaft Engine Speed Sensor state using the recommended Cummins® electronic service tool or equivalent and monitor (Engine Speed Main Sensor State) to check if the sensor state transitions.
Figure 1.5 -Engine Speed Main Sensor State (Low Input Voltage)
Valid Signal = OK
Low Input Voltage, or Degrade = Not OK
→Replace the Engine Crankshaft Speed/Position Sensor (P/N 5491808).
Figure 1.6 - Engine Speed Main Sensor State (Valid Signal)

C. ECM calibration revision history check
→If a calibration update for this fault code is available, the Engine Control Module calibration revision must be that revision or higher.


Read More:









Blog.Teknisi

Subscribe to receive free email updates:

0 Response to "SPN 190 - FMI 2 (Fault Code: Engine Crankshaft Speed/Position - Data Erratic, Intermittent, or Incorrect)"

Post a Comment