Translate

Fuel System Cummins B3.3 and QSB3.3 - Electronic Engine


Flow Diagram
with Mechanically Actuated Injector

B3.3 Engine 

1. Fuel Supply from Tank
2. Hand priming pump
3. Fuel filter
4. Water in fuel sensor
5. Fuel pump
6. Fuel shutoff solenoid
7. High-pressure fuel line
8. Injector
9. Fuel drain manifold
10. Fuel return to tank.
QSB3.3 Engine
1. Fuel supply from tank
2. Water in fuel (not mounted on Engine) (not shown)
3. Fuel filter
4. Fuel supply from fuel filter to fuel pump
5. Fuel pump
6. Fuel supply to high-pressure common rail
7. High-pressure common rail
8. High-pressure fuel lines
9. Injector
10. Fuel drain from injectors
11. Fuel drain to common rail overflow valve fitting
12. Fuel drain to fuel drain manifold
13. Fuel pump overflow to fuel drain manifold
14. Fuel return to tank. 


Electronic Controlled Fuel System
General Information
The ISB, ISC, and ISL with CM2150 electronic control modules (ECM) are electronically operated fuel control systems that also provide many operator and vehicle features.

The base functions of the control system include fueling and timing control, limiting the engine speed operating range between the low and the high idle set points, and reducing exhaust emissions while optimizing engine performance. The system also controls the engine brakes.

The control system uses inputs from the operator and its sensors to determine the fueling and timing required to operate at the desired engine speed at the required emissions level.

ECM Inputs
The ECM is the control center of the system. It processes all of the inputs and sends commands to the fuel system, vehicle, and engine control devices.

The ECM performs diagnostic tests on most of its circuits and will activate a fault code if a problem is detected in one of these circuits. Along with the fault code identifying the problem, a snapshot of engine operating parameters at the time of fault activation is also stored in memory.

Active fault codes will cause a diagnostic lamp to activate to signal the operator.

The ECM can communicate with service tools and some other vehicle controllers (such as transmissions, ABS, ASR, electronic dash displays and so on) through the SAE J1939 data link.

Some vehicles and equipment will have SAE J1939 networks on them that link many of the “smart” controllers together. Vehicle control devices can temporarily command engine speed or torque to perform one of its functions (that is, transmission shifting, anti-lock braking and so on).

The control system utilizes a number of sensors to provide information on engine operating parameters. These sensors include:
→Engine coolant temperature sensor
→Intake manifold air temperature sensor
→Intake manifold pressure sensor
→Engine oil pressure sensor
→Engine speed (crankshaft position) sensor
→Camshaft position sensor
→Barometric pressure sensor
→Rail fuel pressure sensor
→Water-in-fuel sensor
→Turbocharger speed sensor
→Turbocharger compressor inlet air temperature sensor
→Accelerator pedal/lever position sensor
→Engine brake selector switches
→Engine coolant level sensor
→Vehicle speed sensors
→Feature control switches (i.e cruise control switches)
→Fan control switch
→Air conditioner pressure switch
→Remote accelerator
→Remote PTO.
Note : These inputs are application dependent. Some applications will not use all of these inputs.

Engine Protection System
The ISB, ISC, and ISL with CM2150 engines are equipped with an engine protection system. The system monitors critical engine temperatures and pressures, and will log diagnostic faults when an over or under normal condition occurs. If an out-of-range condition exists and engine derate action is to be initiated, the operator will be alerted by an in-cab Warning lamp. The Stop lamp will blink or flash when out-of-range conditions continue to worsen. The driver must pull to the side of the road, when it is safe to do so, to reduce the possibility of engine damage.

Note : Engine power and speed will gradually be reduced, depending on the level of severity of the
observed condition. The engine protection system will not shut down the engine unless the engine protection shutdown feature has been enabled.


Read More:
Fuel System Cummins ISX15 CM2350 - Electronic Engine







Blog.Teknisi

Subscribe to receive free email updates:

2 Responses to "Fuel System Cummins B3.3 and QSB3.3 - Electronic Engine"