Translate

SPN 111 - FMI 4 (Fault Code 196 - Two Wire Sensor)

SPN 111 - FMI 4 (Fault Code: 196 - Two Wire Sensor)
SPN111 FMI4
ISB, ISC and ISL with CM2150 - Engine Coolant Level Sensor 1 Circuit

CODES:
Fault Code: 196
PID(P), SID(S): P111
SPN: 111
FMI: 4/4
Lamp: AMBER
SRT:

REASON: Coolant Level Sensor 1 Circuit - Voltage Below Normal or Shorted to Low Source. Low signal voltage detected at the engine coolant level circuit.

EFFECT: None on performance.

Circuit Description:
The engine coolant level sensor is a switch and is used to measure the level of the engine coolant in the radiator top tank. The coolant level sensor is immersed in the coolant and returns a different signal voltage when immersed in coolant versus being out of coolant. The electronic control module (ECM) supplies 5 volts to the coolant level signal circuit. The resistance of the engine coolant level sensor changes based on the coolant level. The sensor resistance is between 5.4k ohms and 34k ohms when the sensor is submersed in coolant. The sensor resistance is between 333k ohms and 880k ohms when the sensor is not submersed in coolant. The ECM monitors the change in voltage caused by changes in the resistance of the sensor to determine the level of the engine coolant.

Component Location:
The engine coolant level sensor is typically located in the radiator top tank or surge tank.

Conditions for Running the Diagnostics:
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.

Conditions for Setting the Fault Codes:
The ECM detects that the coolant level signal voltage is less than 0.258-VDC for more than 20 seconds.

Action Taken When the Fault Code is Active:
• The ECM illuminates the amber CHECK ENGINE light immediately when the diagnostic runs and fails.
• No engine protection will be available for low coolant level.

Conditions for Clearing the Fault Code:
The ECM will turn off the amber CHECK ENGINE light immediately after the diagnostic runs and passes.

Shop Talk:

  • Verify the electronic control module (ECM) calibration is correct. Check the calibration revision history found on QuickServe® Online for applicable fixes to the calibration stored in the ECM. If necessary, recalibrate the ECM.

Possible causes of this fault code include:
• Signal circuit shorted to ground or return in the harness, sensor, or connectors.


Read More:
SPN 111 - FMI 3 (Fault Code 195 - Two Wire Sensor)
SPN 111 - FMI 3 (Fault Code 195 - Three Wire Sensor)







Blog.Teknisi

Subscribe to receive free email updates:

12 Responses to "SPN 111 - FMI 4 (Fault Code 196 - Two Wire Sensor) "

  1. Hi! This is my first visit to your blog! We are a team of volunteers and new initiatives in the same niche. Blog gave us useful information to work. You have done an amazing job! Fault Location Services Franconia

    ReplyDelete
  2. What a fantabulous post this has been. Never seen this kind of useful post. I am grateful to you and expect more number of posts like these. Thank you very much. Fault Location Services Laurel Hill

    ReplyDelete
  3. Appreciate it intended for placing a really good document! I stumbled upon your blog perfect for the desires. Its full of superb in addition to very helpful threads. Sustain the favorable do the job! Fault Location Services Crofton

    ReplyDelete
  4. These gadgets should be practical and designed to meet the necessities of most clients. wire rope manufacturer in malaysia

    ReplyDelete
  5. Here at this site really the fastidious material collection so that everybody can enjoy a lot. Coinex referral code

    ReplyDelete
  6. Corsair Hydro XL5 Coolant in UAE, Hydro X Series Performance Coolant in UAE, 1L Coolant in UAE
    https://gccgamers.com/corsair-xl5.html
    Corsair Hydro XL5 Coolant in UAE, Safe Shopping Multiple Payment Options Express Delivery GCC Gamers Moneyback Guarantee.
    1634277993256-9

    ReplyDelete
  7. I got problem with hyundai 145cr9.
    Code error spn 3509 fmi4

    ReplyDelete
  8. what number is on the ecm or harness to ohm to the sensor. I have an error code 196which wires do I check for voltage coming from ecm. Because I have no voltage going to coolant level sensor 2 wire.

    ReplyDelete
  9. SNP 111 FMI 4 ariza kodu var silinmiyor sebep ne olabilir

    ReplyDelete
  10. Hüdayi 770-9 loder makina var SNP 111 FAMI 4 ariza kodu yanıyor ve perfomans düşüklüğü yapıyor sorunu çözemedim ne olabilir

    ReplyDelete