SPN 1112 - FMI 11 (Fault Code 393)
Thursday, July 12, 2018
Fault Codes CUMMINS GTA38 K38 K50 QSK38 QSK50/60 CM850,
Fault Codes CUMMINS Signature ISX QSX15 CM570
SPN1112 FMI11
Engine Brake Actuator Driver 3 Circuit - Root Cause Not Known
CODES:
Fault Code: 393
PID(P), SID(S): S82
SPN: 1112
FMI: 11/11
Lamp: Amber
REASON: Low voltage detected at engine brake circuit 3.
EFFECT: None on performance.
Circuit Description:
The Engine Control Module (ECM) enables the engine brake by sending a signal directly to the engine brakes.
Component Location:
The engine brakes are located under the valve cover.
Conditions for Running the Diagnostics:
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes:
The Engine Control Module (ECM) detected low voltage at the engine brake circuit 3.
Action Taken When the Fault Code is Active:
• The ECM illuminates the amber CHECK ENGINE lamp and/or the malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.
Conditions for Clearing the Fault Code:
• To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
• The fault code status displayed by the recommended Cummins® electronic service tool or equivalent will change to INACTIVE immediately after the diagnostic runs and passes.
• The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
• The “Reset All Faults” command in the recommended Cummins® electronic service tool or equivalent can be used to clear active and inactive faults.
Shop Talk:
Possible causes of this fault code include:
• Engine brake circuit 3 shorted to ground.
Read More:
SPN 635 - FMI 6 (Fault Code 395)
SPN 635 - FMI 5 (Fault Code 394)
Blog.Teknisi
Engine Brake Actuator Driver 3 Circuit - Root Cause Not Known
 |
| Engine Brake Relay Supply Circuit |
CODES:
Fault Code: 393
PID(P), SID(S): S82
SPN: 1112
FMI: 11/11
Lamp: Amber
REASON: Low voltage detected at engine brake circuit 3.
EFFECT: None on performance.
Circuit Description:
The Engine Control Module (ECM) enables the engine brake by sending a signal directly to the engine brakes.
Component Location:
The engine brakes are located under the valve cover.
Conditions for Running the Diagnostics:
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes:
The Engine Control Module (ECM) detected low voltage at the engine brake circuit 3.
Action Taken When the Fault Code is Active:
• The ECM illuminates the amber CHECK ENGINE lamp and/or the malfunction indicator lamp (MIL) immediately when the diagnostic runs and fails.
Conditions for Clearing the Fault Code:
• To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
• The fault code status displayed by the recommended Cummins® electronic service tool or equivalent will change to INACTIVE immediately after the diagnostic runs and passes.
• The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
• The “Reset All Faults” command in the recommended Cummins® electronic service tool or equivalent can be used to clear active and inactive faults.
Shop Talk:
Possible causes of this fault code include:
• Engine brake circuit 3 shorted to ground.
Read More:
SPN 635 - FMI 6 (Fault Code 395)
SPN 635 - FMI 5 (Fault Code 394)
Blog.Teknisi
0 Response to "SPN 1112 - FMI 11 (Fault Code 393)"
Post a Comment